Skip to product information
1 of 6

M-Jet Supersprint v1.0 Build Kits

M-Jet Supersprint v1.0 Build Kits

Regular price $49.99 USD
Regular price $0.00 USD Sale price $49.99 USD
Save! Sold out
Shipping calculated at checkout.
Kit Type

Build Kits for the M-Jet Supersprint v1.0 RC Jet Boat. We've built many 3d printable boats and the M-Jet Supersprint is by far the best one we've built yet so we've developed some build kits to help make your summer a little more fun and get you out on the lake! We have three different styles of kits including:

  • Hardware Only
  • Electronics Only
  • Hardware and Electronics
  • Printed Plastics 

Hardware kits include all necessary fasteners, bearings, heat set inserts, steel rod, brass tube and seals for building the M-Jet Supersprint with either the standard or mini receiver drybox. Each hardware kit contains the following:

80+ stainless steel screws/nuts/washers (various)
22 - m3x5.7x4.6 threaded brass heat set inserts
1 - m5x119 smooth stainless rod
1 - m5x112 smooth stainless rod
2 - m3x38 smooth stainless rod
1 - m3x22 smooth stainless rod
1 - m3x62 smooth stainless rod
5 - 3x4mm x25mm brass tube
1 - 5mm OD x 30mm spring
1 - O-ring 22x26x2
1 - O-ring 29x33x2
2 - FKM rotary shaft oil seal 5x15x6mm
1 - 5mm to 5mm brass motor coupler
2 - 5x13x4mm stainless steel bearings

All fasteners and bearings are 304 stainless steel for enhanced corrosion resistance. All screws are metric sizes with hexagonal drive sockets. Various sizes of rod are cut to length however flat spots will need to be ground down in appropriate spots as per the build guide.

Electronics kits will include a set of appropriate electronics and water cooling parts required to build the model but will not include batteries, controllers or receivers which must be purchased separately. The motor and ESC in our kit is meant to be paired with a 3s LIPO battery for good performance but can also be used with a 4S LIPO for maximum performance (comparison). This kit includes:

1 - PowerHD TR-4 Waterproof Metal Gear Micro Servo 2.6KG (link)
1 - 20mm Circular Servo Arm (link)
2 - 10cm 22AWG Servo Extension cables (link)
1 - ZTW Shark G2 100A Brushless ESC (water-cooled with XT60+4mm banana plugs) (link)
1 - Surpass Hobby 2150KV Rocket RC 3660 Brushless 4 Pole RC Boat Motor (5.0mm  drive shaft and 4mm banana plugs) (link)
1 - Surpass Hobby Rocket RC 3660 water cooling jacket (36-S) (link)
60cm (2') - 3x5mm silicon water cooling tube (link)

Printed Plastics kits provide all necessary 3D-printed parts to complete the build. Most pieces are made from PLA, with some TPU and ABS components where needed. Due to the nature of 3D printing, slight imperfections may be present, but they won’t impact the performance. Assemble the plastics as per the designer's build guide. 3D prints are not guaranteed to be watertight so it is recommended to paint or epoxy the hull after gluing. The kit includes all items shown in the product photo in the colors displayed, including:

  • Yellow PLA hull
  • Black TPU seal
  • Two nose options, TPU and PLA
  • Red ABS motor mount
  • Two sets of fins PLA (long 15, short 20) 
  • Three nozzles PLA (+5, +10, +15)
  • Red PLA original and mini dry boxes options for receiver
  • PLA frame, roll cage, drivers, and motor
  • PLA intake grate, ride plate, pump, and impeller

3D Printed plastic parts are not indestructible and may break over time. You are solely responsible for repairing or replacing any broken parts as required. These printed parts are sold with permission from the designer and a portion of the sale goes to support their work.

Looking for the build files? Buy them here.
Need a controller? Try the FlySky GT5.

OUR KITS ONLY COME WITH THE PARTS LISTED ABOVE TO ASSIST YOU IN YOUR BUILD. OTHER PARTS WILL LIKELY BE REQUIRED TO COMPLETE YOUR BUILD.

keywords: screw kit, hardware kit, fastener kit, fastener set, screw set, screw kit, bearing kit, bearing set, rc boat, jetboat, jet boat, mjet sprint, m-jet super sprint, 3d printed, 3d rc, 3d printed boat.

View full details